draft PostScript body parts Jan 96
Carrying PostScript in X.400 and MIME
Fri Jan 5 09:55:37 MET 1996
Harald Tveit Alvestrand
UNINETT
Harald.T.Alvestrand@uninett.no
Status of this Memo
The name of this draft is draft-ietf-mixer-
postscript-00.txt
The following text is required for all drafts:
This document is an Internet Draft. Internet Drafts
are working documents of the Internet Engineering
Task Force (IETF), its Areas, and its Working Groups.
Note that other groups may also distribute working
documents as Internet Drafts.
Internet Drafts are draft documents valid for a
maximum of six months. Internet Drafts may be
updated, replaced, or obsoleted by other documents at
any time. It is not appropriate to use Internet
Drafts as reference material or to cite them other
than as a "working draft" or "work in progress."
Please check the I-D abstract listing contained in
each Internet Draft directory to learn the current
status of this or any other Internet Draft.
This document is an update to part of RFC 1494.
Please send comments to the MIXER mailing list:
<ietf-mixer@innosoft.com>
Alvestrand Exp July 96 [Page 1]
draft PostScript body parts Jan 96
1. Introduction
This document describes methods for carrying PostScript
information in the two standard mail systems MIME and
X.400, and the conversion between them. It uses the
notational conventions of [BODYMAP], and the conversion is
further described in [MIXER].
2. The PostScript body part
Carrying PostScript in X.400 was originally defined in RFC
1494. This specification carries that work forward now
that RFC 1494 is obsoleted by [BODYMAP].
The following Extended Body Part is defined for PostScript
data streams. It has no parameters.
postscript-body-part EXTENDED-BODY-PART-TYPE
DATA OCTET STRING
::= mime-postscript-body
mime-postscript-body OBJECT IDENTIFIER ::=
{ mixer-bp-data 2 }
3. The Application/PostScript content-type
In MIME, PostScript is carried in the body part
"application/PostScript", which is defined in RFC 1521.
4. MIXER conversion
X.400 Body Part: Extended Body Part, OID mime-postscript-body
MIME Content-Type: application/postscript
Conversion Type: No conversion
The two representations of PostScript both contain a
single stream of octets. This stream of octets can be
copied with no problems between the representations. No
other data needs to be converted.
Alvestrand Exp July 96 [Page 2]
draft PostScript body parts Jan 96
5. OID Assignments
This OID is also defined in [BODYMAP].
POSTSCRIPT-MAPPINGS DEFINITIONS ::= BEGIN
EXPORTS -- everything --;
IMPORTS
mixer-bp-data
FROM MIXER-MAPPINGS
id-mime-postscript-body OBJECT IDENTIFIER ::=
{ mixer-bp-data 2 };
END
6. Security issues
The issues concerning PostScript and security are well
discussed in RFC 1521. No additional security issues are
identified by this memo.
7. Trademark issues
PostScript is a trademark of Adobe Systems, Inc.
8. References
[MIXER]
S.E. Hardcastle-Kille, MIXER: Mapping between X.400
and RFC 822/MIME (in preparation)
[BODYMAP]
Mapping between X.400 and RFC 822/MIME message bodies
(in preparation)
Alvestrand Exp July 96 [Page 3]
draft PostScript body parts Jan 96
9. Author's address
Postal: Harald Tveit Alvestrand
UNINETT
Postboks 6883 Elgeseter
N-7002 TRONDHEIM
Tel : +47 73 59 70 94
Email : Harald.T.Alvestrand@uninett.no
Table of Contents
Status of this Memo ................................ 1
1 Introduction ...................................... 2
2 The PostScript body part .......................... 2
3 The Application/PostScript content-type ........... 2
4 MIXER conversion .................................. 2
5 OID Assignments ................................... 3
6 Security issues ................................... 3
7 Trademark issues .................................. 3
8 References ........................................ 3
9 Author's address .................................. 4
Table of Contents .................................. 4
Alvestrand Exp July 96 [Page 4]